How to Set up a Tub Yourself
How to Set up a Tub Yourself
Blog Article
The article which follows about A Step-by-Step Guide to Installing a Bathtub is without a doubt fascinating. You should take a look.
Setting up a bathtub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, and in some cases, tiling skills. Replacing an old tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily obtainable, the task can move immediately; if you have to open a wall surface to remove the old tub as well as place the new tub, the job is much harder. In either instance, the project is within a house handyman's abilities, although you will need a helper to vacate the old tub as well as embeded in the brand-new one. Ensure you have certified on your own for the job as well as fit trying it. Rather than employing a service provider to take control of a halfway-completed project, it is much better to take into consideration using one prior to you begin. Chances are you may need an expert plumber to make tube links.
This article will aid you set up a brand-new bath tub in your washroom if you have already purchased a new bathtub as well as do not require to transform the arrangement of your previous water supply pipes.
Your tools as well as product list must consist of the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, switch on the faucets to drain any type of water staying in the system. The process of eliminating the existing taps can be quite problematic due to the restricted access that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. Once the supply pipelines have been removed, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. As soon as the faucets have been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Before going on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines are in area between the faucet and the sink. Safeguard the tap in place with the producer given backnut. Once the faucet is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type must be attached to the tap finishes first, tightening just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Bathtub
Using the two wood boards under its feet, place the tub in the called for position. The wood boards are practical in equally spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub until the spirit level reviews level.
To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipe by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as inspect all joints and also new pipework for leaks and tighten them if needed. Load the bath tub and also inspect the overflow electrical outlet and also the regular outlet for leakages.
Finally, repair the bath paneling as explained in the producer's user's manual. Tiling and also securing around the bath tub needs to wait until the bathtub has been used at least once as this will settle it into its final setting.
Getting ready for the Setup
To start with, the sustaining structure provided with the bathroom should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is essential to ensure that if the tap comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to avoid strain on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use all of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to now prepare to be fitted in its final placement.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break a rigid seal, creating the water to permeate the wall between the bathroom and also the tiling, resulting in complications with wetness as well as feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with twists of drenched newspaper or soft rope. Remember to constantly load the tub with water before securing, to enable the movement experienced when the tub remains in use. The sealant can fracture relatively early if you do not think about this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly available on the marketplace. It is a good idea to fit the ceramic tiles making use of water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that content about How to Install a Bathtub while doing a lookup on the web. Those who appreciated our blog post plz do not forget to pass it around. Thanks so much for taking the time to read it.
Book Appointment Now
Report this page